Welcome to GuangYuan · GuangZhiYuan Technology! Contact number: 0769-22780950
中文 | English | Online message | Contact us
-
Consultation hotline
0769-22780950
Tell：0769-22780950
Fax：0769-22780951
E-MAIL：gybp@263.net
Add：No. 2, Xiheng 2nd Road, Bajiaowo Industrial Zone, Wanjiang
District, Dongguan City, Guangdong Province,China.
Common problem
What are the unreasonable structural designs that cause cracks in induction quenching parts?
Source： Time：2021-06-01 11:17:10 views：
1. Product design, the same quenching section is uneven, resulting in uneven heating, and the most easily quenching of the transition section.
2. The wider the shoulders of the step axis, the more cracks of the shoulders; the smaller the shoulders r, the stress is concentrated, the temperature is not easy, and it is not easy to quench.
1. Product design, the same quenching section is uneven, resulting in uneven heating, and the most easily quenching of the transition section.
2. The wider the shoulders of the step axis, the more cracks of the shoulders; the smaller the shoulders r, the stress is concentrated, the temperature is not easy, and it is not easy to quench.
3. There is a hole in the hardened layer, the larger the aperture, and the vortex is easily concentrated at the edge of the hole; the temperature is too high, easy to quench. A typical example is a quenching crack on the crank edge of the crankshaft of 1-1.
4. The ends of the key channel are chamfered in the end of the shaft, and there are sharp corners on the parts. The current is concentrated, and it is easy to quench.
5. The machining knife is too deep, that is, the surface roughness value is too large, and crack is easily generated.
2. The wider the shoulders of the step axis, the more cracks of the shoulders; the smaller the shoulders r, the stress is concentrated, the temperature is not easy, and it is not easy to quench.
3. There is a hole in the hardened layer, the larger the aperture, and the vortex is easily concentrated at the edge of the hole; the temperature is too high, easy to quench. A typical example is a quenching crack on the crank edge of the crankshaft of 1-1.
4. The ends of the key channel are chamfered in the end of the shaft, and there are sharp corners on the parts. The current is concentrated, and it is easy to quench.
5. The machining knife is too deep, that is, the surface roughness value is too large, and crack is easily generated.
Related News
More>>- What are the heat treatment equip... 2022-07-21
- Use and maintenance of quenching ... 2021-12-02
- How much is the new induction hea... 2021-09-17
- What are the induction heating eq... 2021-09-13
- What are the components of induct... 2021-08-27
- What aspects are medium frequency... 2021-08-23
- How to choose high frequency indu... 2021-07-30
- Which is a good induction heating... 2021-07-28
- What do you know about induction ... 2021-07-22
- Do you know how to choose an indu... 2021-07-20
- Tell
- 0769-22780950
DongGuan GuangZhiYuan Electronics Technology Co.,Limited | Guang Yuan Technology(HK) Electronics Co.,Limited | DongGuan WanJiang GuangYuan Inverter Electronic Equipment Factory
National consultation hotline：0769-22780950 E-MAIL：gybp@263.net
Add：No. 2, Xiheng 2nd Road, Bajiaowo Industrial Zone, Wanjiang
District, Dongguan City, Guangdong Province,China.
粵ICP備16082297號-1 網站地圖 網站地圖 技術支持：品尚網絡
*本站相關網頁素材及相關資源均來源互聯網，如有侵權請速告知，我們將會在24小時內刪除*
